Stirrer Accessories
Chemglass Life Sciences Stirrer Bearing with side Hose Connection, PTFE, Complete, fits 10mm Shaft, 29/42 Inner Joint
Stirrer Bearing with side Hose Connection, PTFE, Complete, fits 10mm Shaft, 29/42 Inner Joint. PTFE stirrer bearing with a hose connection for vacuum or inert gas source on a single neck flask. Grease-free design has only glass and PTFE in contact with the reaction, and can be used under moderate vacuum applications. Bearing consists of a threaded glass adapter having the listed inner joint size, a saddle o-ring, a body bushing with a compression and locking nut, and a precision PTFE inner bearing. Saddle o-ring provides vacuum tight seal and is replaceable at a fraction of the cost of the entire bearing. Hose connection is 10mm at the largest serration. PLEASE NOTE: FOR USE ONLY WITH CG-2078 OR CG-2079 PRECISION GROUND AND POLISHED STIRRER SHAFTS.
Chemglass Life Sciences 6mm Stirrer Bearing, 14/20
6mm Stirrer Bearing, 14/20. Replacement part for CG206001 Micro Stirrer Assembly.
Chemglass Life Sciences Stirrer Blade, PTFE, Banana Shape, Perforated, 10mm, for 20000mL Flasks, 55/50 minimum joint clearance
Stirrer Blade, PTFE, Banana Shape, Perforated, 10mm, for 22000mL Flasks, 55/50 minimum joint clearance. Blade is shaped to resemble the contour of a round bottom flask. Blades are perforated. Made of 1/8" PTFE to fit 10mm OD stirrer shafts. Minimum joint size listed is the size required to allow passage of the blade.
Chemglass Life Sciences 10mm Stirring Shaft, Chem-Stir, Polished, For Use With 300mL-500mL Flasks, 405mm OAL, Complete with PTFE Nut and Bolt
10mm Stirring Shaft, Chem-Stir, Polished, For Use With 300mL-500mL Flasks, 405mm OAL, Complete with PTFE Nut and Bolt. A 10mm OD precision ground and polished stirrer shaft with our patented** Chem-Stir blade attachment system. Shaft (C) has been manufactured with a ring at the lower end to permit attachment of the blade (B) with a PTFE nut (D) and bolt (A). Shaft is supplied complete with PTFE nut and bolt set. For use with PTFE bearings such as the CG-2077. Polished shaft will not cause abrasion to the sealing surfaces of the PTFE bearing, thereby allowing a vacuum tight seal. Uses the same PTFE nut and bolt blade attachment method as the CG-2074 ground shaft. PLEASE NOTE: STIRRER BLADES MUST BE PURCHASED SEPARATELY.THESE SHAFTS ARE NOT TO BE USED WITH ANY TYPE OF GLASS BEARING. FOR GROUND SHAFTS USED WITH GLASS BEARINGS SEE CG-2074.
Chemglass Life Sciences Stirrer Blade, PTFE, Banana Shape, Perforated, 19mm, Heavy Duty, for 2000mL Flasks, 34/45 minimum joint clearance
Stirrer Blade, PTFE, Banana Shape, Perforated, 19mm, Heavy Duty, for 2000mL Flasks, 34/45 minimum joint clearance. Blade is shaped to resemble the contour of a round bottom flask. Blades are perforated. Made of 3/16" PTFE to fit 19mm OD stirrer shafts. Minimum joint size listed is the size required to allow passage of the blade.
Ace Glass, Inc. Bearing, PTFE, non-shedding, low-vacuum, 24/40 inner joint, accepts 10mm OD stir shaft
Bearing, PTFE, non-shedding, low-vacuum, 24/40 inner joint, accepts 10mm OD stir shaft
Ace Glass, Inc. BEARING,GLASS,10MM, NO 15
Glass bearing design for use with Ace-Thred pressure reactors and our 8075 glass, polished or 8074 bare, stainless steel 10mm stirring shafts. Both the top bushing and bottom coupling are PTFE. Bearing,glass,10mm,#15-#15
Sigma Aldrich Fine Chemicals Biosciences PTFE stirrer shaft shaft diam. 10 mm, L 650 mm | 1EA
PTFE stirrer shaft shaft diam. 10 mm, L 650 mm | 1EA
Glas Col LLC Stirrer Accessory
90 degree clamp for 1/2" to 3/4" diameter rod, used with sitrring systems and stir tester systems.
Arrow Engineering S-316-18 Type 316 Stainless Steel 18" Propeller Shaft
All Arrow Mixing Products' stainless steel mixer shafts are 3/8" dia. & made of 316 stainless steel. These quality mixer parts have a 5/16-24 external thread for easy assembly with all of our stainless steel propellers and couplings. (Note: propeller and coupling sold separately)
Ace Glass, Inc. 10mm 64cm stainless steel stir shaft, PTFE covered, drilled type
64cm long PTFE-covered, 10mm O.D. stainless steel drilled-type stirring shaft. Can be used unlubricated with a water-cooled Trubore bearing to achieve 500 rpm maximum. When used with a Trubore bearing lubricated with stir-lube, 1500 rpm maximum can be achieved. When used with a condensate film as an added heat transfer agent, 2000 rpm maximum can be achieved.
Chemglass Life Sciences 10mm Stirring Shaft, Chem-Stir, Polished, For Use With 2L-12L Flasks, 530mm OAL, Complete with PTFE Nut and Bolt
10mm Stirring Shaft, Chem-Stir, Polished, For Use With 2L-12L Flasks, 530mm OAL, Complete with PTFE Nut and Bolt. A 10mm OD precision ground and polished stirrer shaft with our patented** Chem-Stir blade attachment system. Shaft (C) has been manufactured with a ring at the lower end to permit attachment of the blade (B) with a PTFE nut (D) and bolt (A). Shaft is supplied complete with PTFE nut and bolt set. For use with PTFE bearings such as the CG-2077. Polished shaft will not cause abrasion to the sealing surfaces of the PTFE bearing, thereby allowing a vacuum tight seal. Uses the same PTFE nut and bolt blade attachment method as the CG-2074 ground shaft. PLEASE NOTE: STIRRER BLADES MUST BE PURCHASED SEPARATELY.THESE SHAFTS ARE NOT TO BE USED WITH ANY TYPE OF GLASS BEARING. FOR GROUND SHAFTS USED WITH GLASS BEARINGS SEE CG-2074.
Chemglass Life Sciences Stirrer Bearing, Macro, Glass, with tooled Lubricant Cup, for 10mm Shaft, 29/26 Inner Joint
Stirrer Bearing, Macro, Glass, with tooled Lubricant Cup, for 10mm Shaft, 29/26 Inner Joint. Similar to CG-2070 but with a tooled lubricant cup at the top of the bearing to hold an increased amount of lubricant. NOTE: Not for use with CG-2078 or CG-2079 polished stirrer shafts.
Chemglass Life Sciences Diameter x Height (mm): 125 x 69, Reactor Size: 2L-5L
Diameter x Height (mm): 125 x 69, Reactor Size: 2L-5L. Heavy duty PTFE anchor made of 0.500 thick PTFE. Blade is shaped to mirror the contour of Chemglass cylindrical reactors. Designed for use with CG-2078 Chem-Stir 10mm stirrer shaft. The blade is secured to the stirrer via a PTFE pin. PLEASE NOTE: CG-2081-A-02 IS NOT RECOMMENDED FOR USE WITH BAFFLES OR THERMOCOUPLES.
Chemglass Life Sciences Stirrer Blade, PTFE, Banana Shape, Solid, 10mm, for 1000mL Flasks, 34/45 minimum joint clearance
Stirrer Blade, PTFE, Banana Shape, Solid, 10mm, for 1000mL Flasks, 34/45 minimum joint clearance. Blade is shaped to resemble the contour of a round bottom flask. Blades are solid. Made of 1/8" PTFE to fit 10mm OD stirrer shafts. Minimum joint size listed is the size required to allow passage of the blade.